Computer aided surgery : official journal of the International Society for Computer Aided Surgery
-
Comput. Aided Surg. · Jan 2014
RapidSplint: virtual splint generation for orthognathic surgery - results of a pilot series.
Within the domain of craniomaxillofacial surgery, orthognathic surgery is a special field dedicated to the correction of dentofacial anomalies resulting from skeletal malocclusion. Generally, in such cases, an interdisciplinary orthodontic and surgical treatment approach is required. After initial orthodontic alignment of the dental arches, skeletal discrepancies of the jaws can be corrected by distinct surgical strategies and procedures in order to achieve correct occlusal relations, as well as facial balance and harmony within individualized treatment concepts. To transfer the preoperative surgical planning and reposition the mobilized dental arches with optimal occlusal relations, surgical splints are typically used. For this purpose, different strategies have been described which use one or more splints. Traditionally, these splints are manufactured by a dental technician based on patient-specific dental casts; however, computer-assisted technologies have gained increasing importance with respect to preoperative planning and its subsequent surgical transfer. ⋯ In this pilot study it was demonstrated that clinically usable splints for orthognathic surgery can be produced by computer-assisted technology. Virtual splint design was realized by RapidSplint®, an in-house software platform which might contribute in future to shorten preoperative workflows for the production of orthognathic surgical splints.
-
Comput. Aided Surg. · Jan 2014
3D atlas-based registration can calculate malalignment of femoral shaft fractures in six degrees of freedom.
This study presents and evaluates a semi-automated algorithm for quantifying malalignment in complex femoral shaft fractures from a single intraoperative cone-beam CT (CBCT) image of the fractured limb. ⋯ This atlas-based algorithm quantified malalignment in complex femoral shaft fractures within clinical tolerances from a single CBCT image of the fractured limb.
-
Comput. Aided Surg. · Jan 2013
Comparative StudyMinimally invasive posterior cervical microforaminotomy in the lower cervical spine and C-T junction assisted by O-arm-based navigation.
Navigated posterior cervical microforaminotomy (PCM) is a promising minimally invasive technique for treating radiculopathy caused by lateral disc herniations and foraminal stenosis. Between December 2009 and October 2010, 14 patients with unilateral foraminal disc herniations or foraminal stenosis at the C6-7 or C7-T1 level underwent PCM assisted by O-arm navigation using the METRx tubular retractor. The main symptoms were radicular arm pain with no significant neck pain. ⋯ The mean operation time was 136 minutes, with the additional time required for the image guided surgery assisted by O-arm-based navigation being approximately 28 minutes on average. There were no other complications during the surgical procedure or in the immediate postoperative period. Posterior cervical microforaminotomy assisted by O-arm-based navigation is a safe, effective and minimally invasive procedure for the treatment of lateral disc herniations and foraminal stenosis of the lower cervical spine and C-T junction, offering the possibility of an accurate decompression with a reduced risk of segmental instability.
-
Comput. Aided Surg. · Jan 2013
Comparative StudyNavigated versus conventional transfixation of AC joint injuries: feasibility and accuracy.
Transfixation of the acromioclavicular (AC) joint is a well-established technique for treating Rockwood IV to VI lesions. However, several complications, including pin breakage or pin migration due to incorrect placement, have been reported in the literature. A cadaveric study was performed to investigate whether the use of 3D navigation might improve the accuracy of AC joint transfixation. ⋯ Three-dimensional navigation may improve the accuracy of AC joint transfixation techniques. However, the radiation time is increased when using the navigated procedure, while the overall operation time remains comparable. Nevertheless, a 3D C-arm with a variable isocentric design is recommended for the acquisition of the shoulder scans.
-
Comput. Aided Surg. · Jan 2012
Comparative StudyComparison of robot-assisted and conventional total knee arthroplasty: a controlled cadaver study using multiparameter quantitative three-dimensional CT assessment of alignment.
A functional total knee replacement has to be well aligned, which implies that it should lie along the mechanical axis and in the correct axial and rotational planes. Incorrect alignment will lead to abnormal wear, early mechanical loosening, and patellofemoral problems. There has been increased interest of late in total knee arthroplasty with robotic assistance. This study was conducted to determine whether robot-assisted total knee arthroplasty is superior to the conventional surgical method with regard to the precision of implant positioning. ⋯ Robot-assisted total knee arthroplasty showed excellent precision in the sagittal and coronal planes of the 3D CT scan. In particular, the robot-assisted technique showed better accuracy in femoral rotational alignment compared to the conventional surgery, despite the fact that the surgeons who performed the operations were more experienced and familiar with the conventional method than with robot-assisted surgery. It can thus be concluded that robot-assisted total knee arthroplasty is superior to conventional total knee arthroplasty.